MSB (Main Distribution Switchboard) is a kind of electrical cabinet installed right after the low voltage substations (from 15kV down to 380VAC), the major function of MSB cabinets is connect & disconnect, safety protection for electrical systems. Rated current can reach approximately 6300A.
STPower - Cable ladder is also known as electric ladder, applied to install electrical wires and cables in factories, apartments, buildings ... is the bearing structure of the system.
Product new: STPower - Distributors and Agents for Electrical products ABB in the central of Vietnam
Cubiele Switchboards which are designed and manufactured in accordance with strict quality management, high stability and secure operation has been widely used in power stations, power distribution station in power companies, industrial parks, residential quarters and factories...
Breakers & Switches are designed for flexibility and reliable performance in a wide variety of applications: power distribution for residential and industrial buildings, HVAC, water pumping stations, data centers
Cable tray (trunking) is the conduit for the installation of wires and cables in factories, apartment buildings, office buildings
Cubiele Switchboards which are designed and manufactured in accordance with strict quality management, high stability and secure operation has been widely used in power stations, power distribution station in power companies, industrial parks, residential quarters and factories...In order to install and operate the Medium Voltage Switchboard, the following requirements are required:
- Understand the principle diagram of the medium-voltage RMU system to install
- Read and connect the secondary connection board for the necessary protection and measurement equipment.
- Read the manufacturer's Installation and Operation Manual
- Prepare all necessary accessories for electrical cabinets such as cable connectors, power cables, redundant power sources, support devices, suitable hand-held mechanical tools
- Carry out the installation: follow the steps in the Installation manual. Use suitable hand-held mechanical tools.
Structure of medium voltage cabinet includes: Enclosure is made of about 2mm thick corrugated iron, insulated plating, switching devices are independent, reasonable and protected by an inner wing of the cabinet.
Medium voltage switchboard includes equipment, electrical panel up to 24KV, used in electricity industry, or in industrial factories, commercial buildings.
A medium-voltage ASSEMBLY shall contain, at a minimum, a main aptomat with the buttons closed and switched off with an intensity equivalent to the sum of the additional loads below to be more than 3 times greater; and an electrical outlet of about 220V to use when cabinet maintenance.
- Before conducting the installation, it is necessary to make a block diagram of the electric part to be installed
- Prepare all necessary auxiliary materials for electrical cabinets such as electrical clues, timers, digital rings, iron bars used to install kt ...
- Carry out the installation: Prepare a piece of plywood or chipboard or iron board depending on the condition, mount the parts on the board.
- Reviewing the system: check the electrical safety of the board with the parts installed on the board. Must be strictly in accordance with the procedure as in the original standard design.
- Check the system with the grid connected in series with a lamp about 300W
Then try again with another load. Proceed to install all other parts in the cabinet.
- Perform pulling wires from the motors into the medium voltage cabinet, pulling back the grid, making the frame for the legs of the cabinet.
Choose the ground wire so that it is reasonable, standard and safe such as: the grounding wire of the cabinet must be of the same type, which is soft, flat, knitted wire ...
To be able to install a medium voltage switchboard system, firstly, the block diagram must be absolutely accurate.
The supplier of prestigious and quality ABB Medium Voltage Switchboards
We are proud to be the exclusive distributor of ABB Group's Medium-voltage equipment in the Central region with the advantage of having products available at warehouse, meeting all construction progress.
If you are in need of buying or installing medium voltage electrical cabinets, come to STPower. We not only provide and install all kinds of medium voltage electrical cabinets, but also a manufacturer of Low Voltage Switchboards, leading manufacturing cable tray ladder Central. Specializing in construction and installation of industrial electrical equipment, industrial electrical systems with many large projects went into operation: Duc Long My Khe Hotel, DRC Factory, Doosan Factory, Cocobay Da Nang, Guest Hoa Binh Green Hotel, ... STPower with a team of electric engineers trained in operating the Middle-earth electricity system in Italy, experienced will make customers / partners completely assured of product quality .
Contact us immediately to choose a technical consultant.
For more information about consulting and quotation, customers / partners please contact:
STPOWER JOINT STOCK COMPANY
Factory: Lot No.47, 2nd Street, Da Nang Industrial Zone, Da Nang City
Office: 02363.959.797 - Hotline: 0905.959.564
Email: info@stpower.com.vn
Website: http://stpower.com.vn/
With the motto: "Right quality - Sufficient quantity" STPower commits to produce products with quality above satisfaction.
Please contact STPower immediately to feel the most dedicated care.
Best regards!
